Leading 10 typical forklift accidents ， forklift operation ought to take notice of these issues ！.

Do not ignore the forklift at the office. If the operation is not good, there will be major mishaps in minutes, and there are lots of accidents including forklifts.

Situation 1: The forklift freight blocked the vehicle driver's view, and the individual ahead can not be discovered, leading to a moving accident.
Situation 2: In order to keep the balance of the forklift when lifting heavy items, the workers used their body weight as the counterweight, which practically caused casualties.
Situation 3: The width of the forklift freight exceeds the allowed width of the course and hangs on the roadside rack, which almost creates an crash.
Situation 4: Forklift is speeding and rolls over throughout a turn.
Case 5: The forklift driver did not see the pedestrian, and the pedestrian did not observe the forklift.
Situation 6: The forklift lifts the personnel illegally, the forklift vehicle driver does not wear the safety belt, the forklift lifter drops and the vehicle driver is crushed when the forklift rolls over.
Instance 7: The forklift chauffeur did not wear a seat belt and fell from the lorry when it surrendered and was squashed.
Forklift procedure need to pay attention to these issues ：.

Begin.
1. Prior to beginning, observe the environments, and after verifying that there are no challenges that prevent the safety of driving, honk the horn first and then start.
2. For vehicles with hydraulic (air pressure) brakes, the brake hydraulic pressure ( atmospheric pressure) gauge should be secure prior to starting.
3. When the forklift begins with a tons, the vehicle driver needs to initially confirm that the load is steady and reputable.
4. The start should be slow-moving and steady.

Driving.
1. When driving, the elevation between the bottom end of the fork and the ground should be kept at 300mm-400mm, and the mast must be slanted backward. .
2. Do not lift the fork too high when driving. When going into and leaving the work site or while driving, beware that there will certainly be no barriers in the sky. When the lots is taking a trip, the fork should not be increased too expensive, which will influence the security of the forklift. .
3. After dumping, the fork ought to be reduced to the typical driving placement before driving. .
4. When turning, if there are pedestrians or cars nearby, the driving signal needs to be released initially. High-speed sharp turns are forbidden. High-speed sharp turns will certainly trigger the automobile to lose lateral security and tip over. .
5. When the forklift is downhill, it is purely forbidden to shut off the flame and slide, and it is forbidden to brake all of a sudden while driving with tons unless there are unique conditions.
6. When the forklift is running, it has to obey the web traffic rules in the factory and have to keep a specific security range from the car ahead. .
7. When the forklift is running, the load needs to remain in the most affordable placement that does not hinder the driving, and the gantry must be effectively slanted back. The lots will not be elevated except when piling or loading. .
8. The elevation of the load need to not block the vehicle driver's sight. In unique conditions, when the thing impacts the forward vision, drive at a low rate when turning around.
9. It is prohibited to switch on the ramp, nor to drive throughout the ramp. .
10. The secure driving speed of the forklift in the manufacturing facility location is 5 km/h, and it has to drive securely at a low speed when entering the manufacturing workshop location. .
11. When the forklift is raised, raised or driven, it is prohibited for employees to depend on the fork to hold things and play a stabilizing duty. .
12. If issues are located, they will certainly be repaired and reported in a timely way, and they will never run with illnesses or conceal them.

loading and dumping.
1. When fork-loading products, the distance between the two forks should be adjusted as required to make the lots of the two forks balanced and not manipulated, and one side of the product should be against the rack. .
2. It is restricted to work with a solitary fork or use a fork top or pull. In unique scenarios, safety indication have to be set up to advise surrounding pedestrians. .
3. In the process of filling and discharging products, the forklift has to be braked with the brake. .
4. The speed of the lorry need to be slow-moving and consistent. Beware not to roll the wheels on the dunnage, so as not to extend the rolled items and hurt people. .
5. When making use of a fork to fork the goods, the fork must be as deep as feasible under the lots, and it needs to be noted that the fork tip must not touch various other products or objects. The tons needs to be supported with very little back tilt of the gantry so that the tons does not slide in reverse. The mast can be tilted onward slightly when the lots is lowered to enable easy positioning of the tons and removal of the forks. .
6. It is restricted to fork goods at high speed and ram difficult things with the fork head. .
7. When the forklift is working, it is prohibited for individuals to stand around the fork, so as to stay clear of the collapse of the goods and injure individuals. .
8. Overloading is banned, and it is banned to make use of forks to lift personnel to participate in high-altitude procedures to stay clear of high-altitude dropping mishaps. .
9. It is not allowed to make use of the brake inertia to slip, put, round or roll items. .
10. It is not allowed to utilize forks to choose, turn pallet discharge.

Leaving .
1. It is prohibited to leave the forklift when the things on the fork are in the air. Prior to leaving the forklift, you should unload the goods or reduced the fork structure.
2. Draw the hand brake deal with to dead or dispirit the emergency brake switch.
3. The engine is switched off and the power is removed. (Except for unique circumstances, such as the driver does not leave the vehicle's line of vision and does not exceed 1 minute).
4. Remove the trick. .

Forklift Operation Precautions.
1. Prior to and after the forklift operation, the appearance needs to be examined, and gas, lubing oil and air conditioning water should be included.
2. Check the safety and security performance of Electric Forklift Truck for Warehouse beginning, running and braking.
3. Examine whether the lights and horn signals are full and efficient.
4. During the procedure of the forklift, examine whether the stress and temperature level are typical.
5. After the forklift is running, the outside leakage must additionally be inspected and the seals ought to be replaced in time.

Forklift Safety Operation Specifications.
1. You have to examine prior to leaving the cars and truck;.
2. When you experience someone before you throughout driving, you ought to send out a signal at a distance of 5 m;.
3. The driving rate in the factory does not exceed 5 km/h;.
4. When driving, the nadir of the freight need to be 0.3 m ~ 0.4 m in the air;.
5. The turning should not be also sharp to avoid the propensity of " complimentary switching";.
6. Adding and down the slope needs to be slow and consistent, Electric Forklift Truck for Warehouse and no switching on the incline is allowed.
7. Do not drive throughout the slope. When the slope is greater than 10%, the automobile ought to be driven backwards when declining;.
8. When the forklift workers carry the goods and move on, if they encounter big or heavy products and most likely to the motorist's line of vision, they ought to take the turning around exercise
.
The "Eight Prohibitions" must be followed in the operation.
1. Single fork procedure is not enabled.
2. It is not permitted to lift the goods for long distance driving.
3. It is not permitted to grab the goods by passing on the pallet with the fork.
4. It is not allowed to straight shovel chemicals, flammables and various other hazardous chemicals with forks.
5. It is not permitted to use inertia pressure to pick up the goods.
6. It is not allowed to make use of stopping force to expatriation round or easy-to-roll objects.
7. It is not allowed to bring individuals to service the pallet or fork, and it is strictly restricted to stand under the fork after the fork is raised.
8. Do not drive laterally on slopes
.
Vehicle parking is not allowed under the following conditions.
1. Curves, slim roads, train crossings;.
2. Areas with a longitudinal incline greater than 5%.
3. When there is an challenge on one side of the road, the contrary side of the area with the exact same size as the obstacle should be within 20 meters at each end.

Web：https://www.onenforklifts.com/
Email：[email protected]
Phone：+86 13827083844